Name:
ASTM A29/A29M-20 PDF
Published Date:
07/01/2020
Status:
Active
Publisher:
ASTM International
1.1 This specification2 covers a group of common requirements which, unless otherwise specified in the purchase order or in an individual specification, shall apply to carbon and alloy steel bars under each of the following ASTM specifications (or under any other ASTM specification which invokes this specification or portions thereof):
| Title of Specification | ASTM |
| Hot-Rolled Carbon Steel Bars: |
|
| Steel Bars, Carbon, Quenched and Tempered | A321 |
| Steel Bars and Shapes, Carbon Rolled from “T'' Rails | A499 |
| Steel Bars, Carbon, Merchant Quality, M-Grades | A575 |
| Steel Bars, Carbon, Hot-Wrought, Special Quality | A576 |
| Steel Bars, Carbon, Merchant Quality, Mechanical Properties | A663/A663M |
| Steel Bars, Carbon, Hot-Wrought, Special Quality, Mechanical Properties | A675/A675M |
| Steel Bars for Springs, Carbon and Alloy | A689 |
| Cold-Finished Carbon Steel Bars: |
|
| Steel Bars, Carbon and Alloy, Cold-Finished | A108 |
| Cold-Drawn Stress-Relieved Carbon Steel Bars Subject to Mechanical Property Requirements | A311/A311M |
| Hot-Rolled Alloy Steel Bars: |
|
| Steel Bars, Alloy, Standard Grades | A322 |
| Carbon and Alloy Steel Bars Subject to End-Quench Hardenability Requirements | A304 |
| Steel Bars, Alloy, Hot-Wrought or Cold-Finished, Quenched and Tempered | A434/A434M |
| Steel Bars, Alloy, Hot-Wrought, for Elevated Temperature or Pressure-Containing Parts, or Both | A739 |
| Cold-Finished Alloy Steel Bars: |
|
| Steel Bars, Alloy, Hot-Rolled or Cold-Finished, Quenched and Tempered | A434/A434M |
| Steel Bars, Carbon, Hot-Wrought or Cold-Finished, Special Quality, for Pressure Piping Components | A696 |
|
|
|
| A These designations refer to the latest issue of the respective specifications, which appear either in the Annual Book of ASTM Standards, Vol 01.05, or as reprints obtainable from ASTM. | |
1.2 In case of any conflict in requirements, the requirements of the purchase order, the individual material specification, and this general specification shall prevail in the sequence named.
1.3 The values stated in either inch-pound units or SI units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall used independently of the other, and values from the two systems shall not be combined.
1.4 For purposes of determining conformance to this specification and the various material specifications referenced in 1.1, dimensional values shall be rounded to the nearest unit in the right-hand place of figures used in expressing the limiting values in accordance with the rounding method of Practice E29.
Note 1: Specification A29/A29M previously listed dimensional tolerances for cold-finished bars; these are now found in Specification A108.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| File Size : | 1 file , 150 KB |
| Note : | This product is unavailable in Russia, Ukraine, Belarus |
| Number of Pages : | 17 |
| Published : | 07/01/2020 |
| Redline File Size : | 2 files , 290 KB |
