ASTM B240-09 PDF

1.1 This specification covers commercial zinc and zinc-aluminum (ZA) alloys in ingot form for remelting for the manufacture of pressure die castings, foundry castings and continuous cast bar stock as designated and specified in Table 1. Seven alloy compositions are specified, designated as follows:

CommonTraditionalASTMAUNSA Alloy 3Zamak 3AG 40AZ33521 Alloy 7Zamak 7AG 40BZ33522 Alloy 5Zamak 5AC 41AZ35530 Alloy 2Zamak 2AC 43AZ35540 ZA-8ZA-8 ...Z35635 ZA-12ZA-12...Z35630 ZA-27ZA-27...Z35840 __________

A See Table 1, footnote B.

1.2 Zinc alloys Z33521, Z33522, Z35530, and Z35540 are used primarily for remelting in the manufacture of pressure die castings. Zinc-aluminum alloys Z35635, Z35630, and Z35840 are used for remelting in the manufacture of both foundry and pressure die castings. Castings made from these ingots are specified in Specification B86, Standard Specification for Zinc and Zinc-Aluminum Alloys for Foundry and Die Castings.

1.3 The values stated in inch-pound units are to be regarded as standard.

1.4 Systems of nomenclature used to designate zinc and zinc-aluminum (ZA) alloys used for casting are described in Appendix X1.

1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.

TABLE 1 Chemical and North American Color Code Requirements

Alloy 3 A, B, C, DAlloy 7 A, B, C, DAlloy 5 A,B ,C ,DAlloy 2 A,B ,C,DZA-8 B, C, EZA-12 B, C, EZA-27 B, C, E Zamak 3Zamak 7Zamak 5Zamak 2ZA-8ZA-12ZA-27 (AG40A)(AG40B)(AC41A)(AC43A) Z33521Z33522Z35530Z35540Z35635Z35630Z35840 Color CodeFNoneBrownBlackGreenBlueOrangePurple Element Aluminum3.9-4.33.9-4.33.9-4.33.9-4.38.2-8.810.8-11.525.5-28.0 Magnesium0.03-0.060.010-0.0200.03-0.060.025-0.050.02-0.030.02-0.030.012-0.020 Copper0.10 max0.10 max0.7-1.12.7-3.30.9-1.30.5-1.22.0-2.5 Iron, Max0.0350.0750.0350.0350.0350.050.07 Lead, Max0.00400.00300.00400.00400.0050.0050.005 Cadmium, Max0.00300.00200.00300.00300.0050.0050.005 Tin, Max0.00150.00100.00150.00150.0020.0020.002 Nickel- - -0.005-0.020- - -- - -- - - - - - - - - ZincGRemainderRemainderRemainderRemainderRemainderRemainderRemainder

A Zinc alloy ingot for die casting may contain nickel, chromium, silicon, and manganese in amounts of up to 0.02, 0.02, 0.035 and 0.05 %, respectively. No harmful effects have ever been noted due to the presence of these elements in up to these concentrations and, therefore, analyses are not required for these elements, except that nickel analysis is required for Z33522.

B ASTM alloy designations were established in accordance with Practice B275. UNS assignations were established in accordance with Practice E527. The last digit of a UNS number differentiates between alloys of similar composition. UNS designations for ingot and casting versions of an alloy were not assigned in the same sequence for all alloys.

C For purposes of acceptance and rejection, the observed value or calculated value obtained from analysis should be rounded to the nearest unit in the last right-hand place of figures, used in expressing the specified limit, in accordance with the rounding procedure prescribed in Practice E29.

D When this material is required to conform to ISO Standard 301, the chemical limits for thallium and indium each shall not exceed 0.001 %.

E Zinc-aluminum ingot for foundry and pressure die casting may contain nickel, chromium, and manganese in amounts of up to 0.01 % each or 0.03 % total. No harmful effects have ever been noted due to the presence of these elements in up to these concentrations and, therefore, analyses are not required for these elements.

F Refer to Practice B908. (Note: Colors indicated are for North American applications.)

G Determined arithmetically by difference.

File Size :	1 file , 86 KB
Note :	This product is unavailable in Russia, Ukraine, Belarus
Number of Pages :	4
Published :	10/01/2009
Redline File Size :	2 files , 160 KB