Name:
ASTM B751-08(2013) PDF
Published Date:
02/01/2013
Status:
Active
Publisher:
ASTM International
1.1 This specification contains various requirements that, with the exception of Sections 6 and 7, are mandatory requirements to the following ASTM nickel and nickel alloy, longitudinally welded tubular product specifications:
Title of Specification
ASTM
Designation
Welded UNS N08020, N08024, and UNS N08026 Alloy Tubes
B468
Welded UNS N08120, UNS N08800, UNS N08810, UNS N08811 Alloy Tubes
B515
Welded Nickel-Chromium-Iron Alloy (UNS N06600, UNS N06603, UNS N06025, and UNS N06045) Tubes
B516
Welded Nickel and Nickel-Cobalt Alloy Tube
B626
UNS N08904, UNS N08925, and UNS N08926 Welded Tube
B674
UNS N08366 and UNS N08367 Welded Tube
B676
Welded UNS N06625, N06219, and N08825 Alloy Tubes
B704
Ni-Cr-Mo-Co-W-Fe-Si Alloy (UNS N06333) Welded Tube
B726
Welded Nickel (UNS N02200/UNS N02201) and Nickel Copper Alloy (UNS N04400) Tube
B730
1.2 One or more of the test requirements of Section 6 apply only if specifically stated in the product specification or in the purchase order.
1.3 In case of conflict between a requirement of the product specification and a requirement of this general specification, only the requirement of the product specification need be satisfied.
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.
TABLE 1 Permissible Variations for Outside Diameter and Wall Thickness of Welded TubeA,BSpecified Outside Diameter
Outside Diameter
Permissible Variations
of Thickness of
Specified Nominal Wall, %
Thickness of
Specified Minimum Wall,%
in. (mm)
+
−
+
−
+
−
Over 0.125 (3.2) to 5/8 (16), excl
0.004 (0.13)
0.005 (0.10)
12.5
12.5
28
0
5/8 (16) to 11/2 (38), incl
0.0075 (0.19)
0.0075 (0.19)
12.5
12.5
28
0
Over 11/2 (38) to 3 (76), incl
0.010 (0.25)
0.010 (0.25)
12.5
12.5
28
0
Over 3 (76) to 41/2 (114), incl
0.015 (0.38)
0.015 (0.38)
12.5
12.5
28
0
Over 41/2 (114) to 6 (152), incl
0.020 (0.51)
0.020 (0.51)
12.5
12.5
28
0
A These permissible variations in outside diameter apply only to material as finished at the mill before subsequent swaging, expanding, bending, polishing, or other fabricating operations.B The ovality provisions of 4.1 apply.| File Size : | 1 file , 100 KB |
| Note : | This product is unavailable in Russia, Ukraine, Belarus |
| Number of Pages : | 6 |
| Published : | 02/01/2013 |
