Name:
ASTM D5966-09 PDF
Published Date:
04/15/2009
Status:
Active
Publisher:
ASTM International
1.1 This engine lubricant test method is commonly referred to as the Roller Follower Wear Test. Its primary result, roller follower shaft wear in the hydraulic valve lifter assembly, has been correlated with vehicles used in stop-and-go delivery service prior to 1993. It is one of the test methods required to evaluate lubricants intended to satisfy the API CG-4 performance category. This test has also been referred to as the 6.2 L Test.
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.2.1 Exceptions - Where there is no direct SI equivalent, such as pipe fittings, thermocouple diameters, and NPT screw threads. Also, roller follower wear is measured in mils.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
1.4 Table of Contents:
| Section | |
| Scope | 1 |
| Referenced Documents | 2 |
| Terminology | 3 |
| Summary of Test Method | 4 |
| Significance and Use | 5 |
| Reagents | 7 |
| Guidelines on Substitution | 7.1 |
| Apparatus | 6 |
| Preparation of Apparatus | 8 |
| New Engine Preparation | 8.1 |
| Installation of Auxiliary Systems and Miscellaneous Components | 8.2 |
| Test Procedure | 9 |
| Description of Test Segments and Organization of Test Procedure Sections | 9.1 |
| Engine Parts Replacement | 9.2 |
| Engine Starting Procedure | 9.3 |
| Normal Engine Shutdown Procedure | 9.4 |
| Emergency Shutdown Procedure | 9.5 |
| Unscheduled Shutdown and Downtime | 9.6 |
| New Engine Break-In | 9.7 |
| Pretest Procedure | 9.8 |
| Fifty-Hour Steady State Test | 9.9 |
| Periodic Measurements | 9.10 |
| Oil Sampling and Oil Addition Procedures | 9.11 |
| End of Test (EOT) Procedure | 9.12 |
| Calculation and Interpretation of Test Results | 10 |
| Environment of Parts Measurement Area | 10.1 |
| Roller Follower Shaft Wear Measurements | 10.2 |
| Oil Analysis | 10.3 |
| Assessment of Test Validity | 10.4 |
| Final Test Report | 11 |
| Reporting Calibration Test Results | 11.1 |
| Report Forms | 11.2 |
| Interim Non-Valid Calibration Test Summary | 11.3 |
| Severity Adjustments | 11.4 |
| Precision and Bias | 13 |
| Precision | 13.1 |
| Precision Estimate | 13.2 |
| Bias | 13.3 |
| Keywords | 14 |
| ANNEXES | |
| Guidelines for Test Part Substitution or Modification | Annex A1 |
| Guidelines for Units and Specification Formats | Annex A2 |
| Detailed Specifications of Apparatus | Annex A3 |
| Calibration | Annex A4 |
| Final Report Forms | Annex A5 |
| Illustrations | Annex A6 |
| Kinematic Viscosity at 100°C Procedure for the Roller Follower Wear Test | Annex A7 |
| Enhanced Thermal Gravimetric Analysis (TGA) Procedure for Soot Measurement | Annex A8 |
| Sources of Materials and Information | Annex A9 |
| APPENDIXES | |
| PC-9 Reference Diesel Fuel Properties | Appendix X1 |
| Diagnostic Data Review | Appendix X2 |
| File Size : | 1 file , 330 KB |
| Note : | This product is unavailable in Russia, Ukraine, Belarus |
| Number of Pages : | 18 |
| Published : | 04/15/2009 |
| Redline File Size : | 2 files , 570 KB |
