Name:
ASTM D6750-13 PDF
Published Date:
05/01/2013
Status:
Active
Publisher:
ASTM International
1.1 These test methods cover the performance of engine oils intended for use in certain diesel engines. They are performed in a standardized high-speed, single-cylinder diesel engine by either the 1K (0.4 % mass fuel sulfur) or 1N (0.04 % mass fuel sulfur) procedure.3 The only difference in the two test methods is the fuel used. Piston and ring groove deposit-forming tendency and oil consumption are measured. Also, the piston, the rings, and the liner are examined for distress and the rings for mobility. These test methods are required to evaluate oils intended to satisfy API service categories CF-4 and CH-4 for 1K, and CG-4 for 1N of Specification D4485.
1.2 These test methods, although based on the original Caterpillar 1K/1N procedures,3 also embody TMC information letters issued before these test methods were first published. These test methods are subject to frequent change. Until the next revision of these test methods, TMC will update changes in these test methods by the issuance of information letters which shall be obtained from TMC (see Annex A15).
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.3.1 Exception-Where there is no direct SI equivalent such as screw threads, national pipe threads/diameters, tubing size, or single source equipment specified. Also Brake Specific Fuel Consumption is measured in kilograms per kilowatthour.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements appear throughout the text. Being engine tests, these test methods do have definite hazards that shall be met by safe practices (see Annex A16 on Safety Precautions).
1.5 The following is the Table of Contents:
|
|
| Section |
| Introduction |
| |
| Scope | ||
| Referenced documents | ||
| Terminology | ||
| Summary of Test Methods | ||
| Significance and Use | ||
| Apparatus | ||
|
| General Laboratory Requirements | |
|
| Test Engine | |
|
| Test Engine Accessories and Parts | |
| Reagents and Materials | ||
| Test Oil Sample Requirements | ||
| Preparation of Apparatus | ||
|
| Engine Inspection | |
|
| Engine Pre-Test Lubrication System Flush | |
|
| Engine Pre-Test Measurements and Inspections | |
|
| Engine Assembly | |
|
| Pressure Testing of Fuel System Assembly | |
| Calibration of Engine Test Stand | ||
|
| General Requirements and Frequency of Calibration | |
|
| Runs | |
|
| Specified Test Parameters | |
|
| Calibration Test Acceptance Criteria | |
|
| Action on Rejection of Calibration Test | |
|
| Test Numbering | |
|
| Reference Oils | |
|
| Severity Adjustments | |
| Engine Operating Procedure | ||
|
| Engine Run-In | |
|
| Cool-Down Procedure | |
|
| Warm-Up Procedure | |
|
| Operating Conditions and Oil Additions | |
|
| Measurement of Oil Consumption | |
|
| Sampling Used Oil | |
|
| Shutdowns, Lost Time and Off Tolerance Conditions | |
|
| Recording of Exhaust Temperature | |
|
| Air-Fuel Ratio Measurement | |
|
| Recording of Engine Conditions | |
|
| Humidity Requirements/Calibration/Measurement | |
| Inspections, Photographs and Measurements | ||
|
| Reference to Reporting Form | |
|
| Pre-Test Measurements of Engine Parts | |
|
| Post-Test Information | |
|
| Oil Inspections | |
| Report | ||
|
| General Directions | |
|
| Electronic Transmission of Test Results (Optional) | |
|
| Reporting Calibration Test Results | |
| Precision and Bias | ||
| Keywords | ||
|
| ANNEXES |
|
| Specifications for Test Engine and Engine Build | ||
| Intake Air System Details | ||
| Exhaust System Details | ||
| Cooling System Details | ||
| Oil System Modifications and Instrument Locations | ||
| Other Pressure and Temperature Measurement Locations | ||
| Oil Consumption Linear Regression Method | ||
| Test Fuel Specifications | ||
| Lubrication System, Flush Apparatus and Procedure | ||
| Engine Operating Conditions | ||
| Procedure for Rating Piston and Liner | ||
| Calculation of Percent Offset and Percent Deviation | ||
| 1K/1N Test Reporting | ||
| Parts List by Part Number (P/N) and Warranty | ||
| Role of Test Monitoring Center | ||
| Safety Precautions | ||
|
| APPENDIXES |
|
| Humidity Data | ||
| Statistical Equations for Mean and Standard Deviation | ||
| Examples of Forms for Reporting | ||
| Optional Recording of Oil Pass Limits | ||
| File Size : | 1 file , 1.1 MB |
| Note : | This product is unavailable in Russia, Ukraine, Belarus |
| Number of Pages : | 69 |
| Published : | 05/01/2013 |
| Redline File Size : | 2 files , 2.8 MB |
