Standard Consumer Safety Specification for Non-Full-Size Baby Cribs/Play Yards

Publisher:
ASTM International

Document status:

Active

Format:

Electronic (PDF)

Delivery time:

10 minutes

Delivery time (for Russian version):

200 business days

SKU:

1.1 This consumer safety specification establishes testing requirements for structural integrity and performance requirements for non-full-size cribs/play yards, both rigid sided and mesh/fabric assemblies. It also provides requirements for labeling and instructional material. The term unit or product will refer to a non-full-size crib/play yard.

1.2 This specification covers a framed enclosure with a floor made for the purpose of providing sleeping or playing accommodations, or both, for a child who cannot climb out and is less than 35 in. (890 mm) in height. It also covers bassinet, changing table, or similar accessories to a non-full-size crib/play yard. These accessories shall also comply with the applicable requirements of ASTM standards addressing those accessories. For example, a changing table that attaches to a play yard shall also comply with the applicable requirements in Specification F2388. This specification does not cover inflatable products.

1.3 No product produced after the approval date of this consumer safety specification shall, either by label or other means, indicate compliance with this specification unless it conforms to all applicable requirements contained herein, before and after all testing.

1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.5 The following safety hazards caveat pertains only to the test method portion, Section 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

Note 1: This consumer safety specification includes the following sections:

Title Section Scope 1 Referenced Documents 2 ASTM Standards 2.1 EN Standards 2.2 ISO Standards 2.3 Federal Regulations 2.4 ANSI Standards 2.5 Terminology 3 Definitions of Terms Specific to This Standard 3.1 Accessory 3.1.24 Accessory Attachment Components 3.1.1 Bassinet/Cradle Accessory 3.1.2 Cantilevered Accessory 3.1.3 Conspicuous 3.1.4 Cord 3.1.5 Corner Post 3.1.6 Dropgate 3.1.7 Dynamic Load 3.1.8 Fabric 3.1.9 Foldable Side or End 3.1.10 Key Structural Elements 3.1.12 Manufacturer's Recommended Use Position 3.1.13 Mattress 3.1.14 Mattress Support Surface 3.1.15 Mesh 3.1.16 Mesh/Fabric Unit 3.1.17 Moveable Side 3.1.18 Non-Full-Size Crib 3.1.19 Non-paper Label 3.1.20 Occupant 3.1.21 Paper Label 3.1.22 Play Yard 3.1.23 Product 3.1.25 Protrusion 3.1.26 Rigid Sided Product 3.1.27 Seam 3.1.28 Static Load 3.1.29 Stationary Side 3.1.30 Strap 3.1.31 Structural Failure 3.1.32 Calibration and Standardization 4 General Requirements 5 Corner Posts 5.1 Scissoring, Shearing, or Pinching 5.6 Latching and Locking Mechanisms 5.8 Openings 5.9 Protective Components 5.10 Labeling 5.11 Stability 5.12 Cords/Straps 5.13 Coil Springs 5.14 Entrapment in Accessories 5.15 Mattress 5.16 Mattresses for Rigid Sided Products 5.17 Protrusions 5.18

Product Details

Published:: 08/01/2024
Number of Pages:: 51
File Size:: 1 file , 4.3 MB
Redline File Size:: 2 files , 7.6 MB
Note:: This product is unavailable in Russia, Ukraine, Belarus

Document History