ISO 23856:2021 PDF

ISO 23856:2021 PDF

Name:
ISO 23856:2021 PDF

Published Date:
06/01/2021

Status:
Active

Description:

Plastics piping systems for pressure and non-pressure water supply, drainage or sewerage - Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin

Publisher:
International Organization for Standardization

Document status:
Active

Format:
Electronic (PDF)

Delivery time:
10 minutes

Delivery time (for Czech version):
200 business days

SKU:
iso-23856-2021_2226409

Choose Document Language:
75.00 €
Need Help?

This document specifies the properties of piping system components made from glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP). It is suited for all types of water supply, drainage and sewerage with or without pressure. Types of water supply include, but are not limited to, raw water, irrigation, cooling water, potable water, salt water, sea water, penstocks in power plants, processing plants and other water-based applications. This document is applicable to GRP UP piping systems, with flexible or rigid joints with or without end thrust load-bearing capability, primarily intended for use in direct buried installations.

NOTE°1°° For the purpose of this document, the term polyester resin (UP) also includes vinyl-ester resins (VE).

NOTE°2°° Piping systems conforming to this document can also be used for non-buried applications, provided the influence of the environment and the supports are considered in the design of the pipes, fittings and joints.

NOTE°3°° This document can also apply for other installations, such as slip-lining rehabilitation of existing pipes.

NOTE°4°° ISO°10467 and ISO°10639, which are replaced by this document, are also referenced in ISO°25780, which specifies requirements for GRP-pipes used for jacking installation.

The requirements for the hydrostatic pressure design of pipes referring to this document meet the requirements of ISO/TS°20656-1 and the general principle for the reliability of structures detailed in ISO°2394 and in EN°1990. These International Standards provide procedures for the harmonization of design practices and address the probability of failure, as well as possible consequences of failures. The design practices are based on a partial safety factor concept, as well as on risk management engineering.

This document is applicable to circular pipes, fittings and their joints of nominal sizes from DN°50 to DN°4000, which are intended to be used for the conveyance of water, sewage and drainage at normal service conditions, with or without pressure.


File Size : 1 file , 4 MB
Note : This product is unavailable in Ukraine, Russia, Belarus
Published : 06/01/2021
Same As : ISO 23856:2021

History

ISO 23856:2021
Published Date: 06/01/2021
Plastics piping systems for pressure and non-pressure water supply, drainage or sewerage - Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin
75.00 €
ISO 10467:2018
Published Date: 06/01/2018
Plastics piping systems for pressure and non-pressure drainage and sewerage - Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin
67.50 €
ISO 10639:2017
Published Date: 10/01/2017
Plastics piping systems for pressure and non-pressure water supply - Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin
67.50 €
ISO 10467/Amd1:2012
Published Date: 03/01/2012
Plastics piping systems for pressure and non-pressure drainage and sewerage - Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin - Amendment 1
5.70 €
ISO 10467:2004
Published Date: 02/01/2004
Plastics piping systems for pressure and non-pressure drainage and sewerage - Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin
62.70 €
ISO 10639:2004
Published Date: 02/01/2004
Plastics piping systems for pressure and non-pressure water supply - Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin
62.70 €

Related products

ISO 3213:2009
Published Date: 09/15/2009
Polypropylene (PP) pipes - Effect of time and temperature on the expected strength
37.20 €
ISO 4440-2:1994
Published Date: 10/01/1994
Thermoplastics pipes and fittings -- Determination of melt mass-flow rate -- Part 2: Test conditions
12.00 €
ISO 18553:2002
Published Date: 03/01/2002
Method for the assessment of the degree of pigment or carbon black dispersion in polyolefin pipes, fittings and compounds
24.30 €
ISO 16871:2003
Published Date: 05/15/2003
Plastics piping and ducting systems - Plastics pipes and fittings - Method for exposure to direct (natural) weathering
24.30 €

Best-Selling Products

INCITS 100-1989(R1995) Add. 1:1991
Published Date: 01/01/1991
Addendum 1 to ANSI/NCITS X3.100-1989, Interface Between DTE & DCE for Packet Mode Operation with Packet Switch Data Communications Networks - NUI and NUI-Derived Facility Extensions (formerly ANSI X3.100-1989(R1995) Add.1:1991)
INCITS 100-1989(R1995)
Published Date: 01/01/1989
Interface Between DTE & DCE for Packet Mode Operation with Packet Switch Data Communications Networks (CCITT X.25) (formerly ANSI X3.100-1989(R1995)
INCITS 103-1983(R1996)
Published Date: 01/01/1983
Unrecorded Magnetic Tape Minicassette For Information Interchange, Coplanar 3.81 mm (0.150 Inch) (formerly ANSI X3.103-1983(R1996))
INCITS 11-1990(R2002)
Published Date: 01/01/1990
Specification for General Purpose Paper Cards for Information Interchange (formerly ANSI X3.11-1990(R2002))
18.00 €
INCITS 111-1986(R1997)
Published Date: 01/01/1986
Matrix Character Sets for Optical Character Recognition (OCR-M) (formerly ANSI X3.111-1986(R1997))
INCITS 112-1984(R1996)
Published Date: 01/01/1984
14-Inch (356 mm) Diameter Low Surface Friction Magnetic Storage Disk (formerly ANSI X3.112-1984(R1996))