Name:
ASTM A888-13a PDF
Published Date:
06/01/2013
Status:
Active
Publisher:
ASTM International
1.2 The EDP/ASA numbers indicated in this section represent a Uniform Industry Code adopted by the American Supply Association (ASA). A group designation prefix, 022, is assigned to hubless products, followed by the four-digit identification assigned to individual items and a check digit. This system has been instituted to facilitate EDP control through distribution channels, and is to be used universally in ordering and specifying product items. Those items with no EDP numbers are either new, special, or transitory and will be assigned numbers on subsequent prints of this specification.
1.3 This specification covers pipe and fittings of the following patterns and applies to any other patterns that conform with the applicable requirements given in this specification.2
| Quarter Bend | Fig. 5 |
| Quarter Bend, Reducing | Fig. 6 |
| Quarter Bend, With Side Opening | Fig. 7 |
| Quarter Bend, With Heel Opening | Fig. 8 |
| Quarter Bend, Tapped | Fig. 9 |
| Quarter Bend, Double | Fig. 10 |
| Quarter Bend, Long | Fig. 11 |
| Short Sweep | Fig. 12 |
| Long Sweep | Fig. 13 |
| Long Sweep, Reducing | Fig. 14 |
| Fifth Bend | Fig. 15 |
| Sixth Bend | Fig. 16 |
| Eighth Bend | Fig. 17 |
| Eighth Bend Long | Fig. 18 |
| Sixteenth Bend | Fig. 19 |
| Sanitary Tee | Fig. 20 |
| Sanitary Tee With Side Opening | Fig. 21 |
| Sanitary Tee With 2 in. Side Opening R or L/R and L | Fig. 22 |
| Sanitary Tee, New Orleans Special With Side Opening | Fig. 23 |
| Sanitary Tee With 45° Side Openings and New Orleans | Fig. 24 |
| Sanitary Special Tee Tapped | Fig. 25 |
| Sanitary Tapped Tee, Horizontal Twin | Fig. 26 |
| Sanitary Tapped Tee, Double Vertical | Fig. 27 |
| Y Branch | Fig. 28 |
| Y Branch, Double | Fig. 29 |
| Y Branch, Upright | Fig. 30 |
| Upright Y Wide Center Florida Special | Fig. 31 |
| Y Branch, Combination 1/8 Bend | Fig. 32 |
| Y Branch, Combination 1/8 Bend Double | Fig. 33 |
| Sanitary Cross | Fig. 34 |
| Sanitary Cross With Side Opening | Fig. 35 |
| Sanitary Cross, New Orleans, With Side Openings | Fig. 36 |
| Sanitary Cross, New Orleans, With 45° Special and | Fig. 37 |
| Sanitary Cross, Tapped | Fig. 38 |
| Test Tee | Fig. 39 |
| Tapped, Extension Piece | Fig. 40 |
| Increaser-Reducer | Fig. 41 |
| Increaser-Reducer, Short | Fig. 42 |
| Tapped Adapter | Fig. 43 |
| Blind Plug | Fig. 44 |
| Iron Body Cleanout-Tapped | Fig. 45 |
| P Trap | Fig. 46 |
| P Trap, Long | Fig. 47 |
| P Trap, Deep Seal | Fig. 48 |
| P Trap, With Primer | Fig. 49 |
| P Trap, With Tapped Inlet | Fig. 50 |
| Tapped Inlet, Double | Fig. 51 |
| Modified Combination Wye and 1/8 Bend, Double | Fig. 52 |
| Modified Combination Wye and 1/8 Bend, Double, Extended | Fig. 53 |
| Two-Way Cleanout | Fig. 54 |
| Twin Cleanout | Fig. 55 |
| Closet Bend, Regular and Reducing | Fig. 56 |
| Closet Flange Riser | Fig. 57 |
| Tapping Bosses | Fig. 58 |
| Double Sweep Sanitary Tee (Extended) | Fig. 59 |
| Running Trap with Double Vents | Fig. 60 |
| P Trap with Tapped or Hubless Side Inlet | Fig. 61 |
| Vented Tub Wye Extended, Double | Fig. 62 |
| Vented Tub Wye Extended Offset, Left or Right | Fig. 63 |
| Vented Tub Wye | Fig. 64 |
| Double Two Way Cleanout | Fig. 65 |
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.5 The committee with jurisdiction over this standard is aware of another comparable standard published by the Cast Iron Soil Pipe Institute, CISPI 301.
| File Size : | 1 file , 670 KB |
| Note : | This product is unavailable in Russia, Ukraine, Belarus |
| Number of Pages : | 58 |
| Published : | 06/01/2013 |
| Redline File Size : | 2 files , 1.6 MB |
